Electrothermal | PartQuest™ Explore

Electrothermal Energy Harvesting - MPPT Capacitor Charging - on Sat, 10/03/2020 - 12:20

lucas.camacho.2018.br
Designer235362

lucas.camacho.2018.br

Member for

3 years 6 months

9

designs

4

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.

The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.

The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:

https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

About text formats

ePower_970

ebookaktiv
Designer152721

ebookaktiv

Member for

6 years 6 months

109

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Electrothermal Energy Harvesting - MPPT Capacitor Charging

Ilmir
Designer197998

Ilmir

Member for

5 years 11 months

5

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

About text formats

Live Electrothermal Energy Harvesting

Mike Donnelly
Designer19

Mike Donnelly

Member for

10 years 5 months

1,541

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

About text formats

Energy Harvesting from TEC12706

JeanVega
Designer152491

JeanVega

Member for

6 years 6 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Electrothermal Energy Harvesting - MPPT Capacitor Charging

Ricardo_1
Designer152396

Ricardo_1

Member for

6 years 6 months

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

About text formats

Electrothermal Energy Harvesting - MPPT Capacitor Charging, Hierarchical

Mike Donnelly
Designer19

Mike Donnelly

Member for

10 years 5 months

1,541

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud for Electrothermal Energy Harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs. The example also illustrates using a sampled-data algorithm for maximum power point tracking (MPPT), to optimize the energy harvest for changing operating temperatures.The design includes a thermoelectric generator (TEG) that is supplied on the "hot" side by a sinusoidally time varying temperature between 75 degC and 100 degC. The "cold" side is held at a fixed 25 degC. The thermal resistance and heat capacitance of the hot-side heat-sink are shown in the schematic. The electronics section includes a mix of analog circuit elements, including an inductor, 1.0 F super-capacitor, LDO regulator and a periodically switched load resistor. It also includes abstract or "math block" models to represent the state-average (non-switching) behavior of a buck-boost converter.The goal of the design is to extract sufficient power from the TEG, to provide a 2.5-Watt/1-second duration power burst once every 10 seconds. This burst is presumably to supply power for a periodic data transmission. The simple MPPT algorithm that helps achieves this is visible in the open-source MPPT-TEG model shown. The MPPT algorithm dynamically adjusts the load current draw from the TEG, to keep it operating at its maximum power output capability. That capability varies with the differential operating temperature. That shift can more easily be seen in the followingTEC/TEG calibration test schematic:https://www.systemvision.com/design/calibrate-tecteg-energy-harvesting

About text formats

Electrothermal Energy Harvesting - Fixed-Current Capacitor Charging

Mike Donnelly
Designer19

Mike Donnelly

Member for

10 years 5 months

1,541

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

NOT FINISHED ...This example is intended to show relevant modeling and simulation capabilities of SystemVision Cloud, for electrothermal energy harvesting (EH) systems. It is not necessarily a practical EH design itself, but rather demonstrates the tool's ability to support knowledgeable users who are creating practical designs.The mechanical and magnetic circuit sections of the model are composed of "physical" models, in that user can directly specify size and physical properties of the components. This includes the mass of the armature, the stiffness of the resonant spring, the cross section area and length of the magnetic core, the residual flux density of the permanent magnet, and the number of winding turns.The electronics section (rectifier and boost converter) contains a mix of passive analog circuit elements as well as abstract or "math block" models to represent the state-average (non-switching) behavior of the converter. Finally, constant power load model represents the power demand for periodic transmission of data typical of an (I)IoT sensor node.In the simulation results displayed on the schematic, the upper right waveform viewer shows the amplitude of the external vibration source (e.g. a motor or transformer housing) of 0.07mm peak at 60 Hz, equivalent to a peak acceleration of 1g (light-blue waveform). The armature spring-mass resonance frequency is 60 Hz, so the armature displacement is seen to reach the frame's travel limit of 4mm peak-to-peak (green waveform).In the upper left, the two waveform viewers are zoomed-in near the 1 second simulation time mark, and they show the air-gap lengths and the corresponding core flux density and winding voltage. Note that the air-gaps are configured in parallel for the flux path, so the effective path reluctance is minimized when either gap approaches zero length.In the lower right, the relatively low value of the rectified "DC" voltage is observed (red waveform), as well as the regulated boost output voltage that supplies the transmitter load.

About text formats

Terms of Use Cookie Notice Data Privacy Notice

lucas.camacho.2018.brDesigner235362

Member for

ebookaktivDesigner152721

Member for

IlmirDesigner197998

Member for

Mike DonnellyDesigner19

Member for

JeanVegaDesigner152491

Member for

Ricardo_1Designer152396

Member for

Mike DonnellyDesigner19

Member for

Mike DonnellyDesigner19

Member for

lucas.camacho.2018.br
Designer235362

ebookaktiv
Designer152721

Ilmir
Designer197998

Mike Donnelly
Designer19

JeanVega
Designer152491

Ricardo_1
Designer152396

Mike Donnelly
Designer19

Mike Donnelly
Designer19