Amplifier | PartQuest™ Explore

Application Area

Galina
Designer21

Galina

Member for

10 years 5 months

104

designs

3

groups

Member of the PartQuest Explore team.

Description

This example shows the bandwidth improvement that results from a cascode amplifier configuration (right-side circuit), compared to a single transistor amplifier configuration (left side).

In these circuits, identical transistor models are used. They are "datasheet" based behavioral models with typical small-signal NFET characteristics. This includes an internal Miller capacitance or Crss, which is set to 10 pF.

In the single transistor circuit, the Miller Theorem states that the effective value of Crss is increased by a factor of (1.0 + A), where A is the gain of the amplifier. In this case the factor is (1.0 + gfs * Rload), or 16x, so the effective Crss = 160 pF. Then the low-pass RC time constant of the input source resistance and the net input capacitance sets the amplifier bandwidth at just under 2 MHz.

For the cascode amplifier, the voltage at the drain of transistor m2 has only very small variation, so the Miller effect is largely suppressed for that device. Transistor m3 amplifies these small voltage changes, but because the current in the Miller capacitance of m3 is drawn from the low impedance gate bias circuit, it does not limit the bandwidth of the amplifier.

You can move the probes around and look at the time-domain or frequency-domain signals at any point in the circuit, to gain more understanding of these component interactions.

About text formats

TEST STAGE Loudspeaker with Simple Amplifier

Galina
Designer21

Galina

Member for

10 years 5 months

104

designs

3

groups

Member of the PartQuest Explore team.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Loudspeaker with Simple Amplifier - on Mon, 12/07/2020 - 22:53

angeltp
Designer237048

angeltp

Member for

3 years 4 months

0

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Loudspeaker with Simple Amplifier - on Wed, 12/02/2020 - 14:39

gilbert.vellet
Designer236968

gilbert.vellet

Member for

3 years 4 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Loudspeaker with Simple Amplifier - on Thu, 11/19/2020 - 13:15

vladimir.jug
Designer236538

vladimir.jug

Member for

3 years 5 months

35

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Loudspeaker with Simple Amplifier - on Sun, 11/15/2020 - 06:24

bbenoit1625
Designer197752

bbenoit1625

Member for

6 years

1

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This simple* analog electronic amplifier design demonstrates the importance of multi-discipline system modeling. A swept frequency response test, from 40 Hz to 1000 Hz, shows the complex amplifier loading effect of the voice-coil and speaker-cone dynamics. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency. The loudspeaker reaches its minimum impedance around 600 Hz, or near 0.6 seconds, where the peak load current is observed.

Normalized component stress monitoring signals are provided in all “datasheet specified” electronics models. For example, the simulation results show that the average power (bjt1/pwr_avg) in the BDP947 NPN BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The corresponding stress monitor (bjt1/stress_ratio_power_avg) normalizes the transistor's average power relative to its 5W rating, so it is easy to see that the component is stressed (i.e. stress_ratio_power_avg &gt; 1.0). Also, the red "hot part monitor", with the junction to solder-point thermal resistance set to 10 C/Watt as given in the datasheet, shows the part temperature rising to well over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

*Note: This is not intended to be a practical amplifier design. There is no blocking capacitor at the output, so it allows undesirable DC current into the voice coil. The purpose is to focus attention on the dynamic characteristics of the loudspeaker and not the circuit itself.

About text formats

Copy of Loudspeaker with Simple Amplifier - on Tue, 10/06/2020 - 17:52

juan.mendozar
Designer235029

juan.mendozar

Member for

3 years 7 months

6

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Copy of Common Emitter Amplifier - on Sun, 10/04/2020 - 20:29

clo21
Designer235403

clo21

Member for

3 years 6 months

6

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Copy of Class A Amplifier - on Wed, 09/16/2020 - 12:24

briangato.bb
Designer234763

briangato.bb

Member for

3 years 7 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Copy of Loudspeaker with Simple Amplifier - on Sat, 09/12/2020 - 13:55

pdhobby1213
Designer234706

pdhobby1213

Member for

3 years 7 months

2

designs

1

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This "Live" example design includes a simple analog electronic amplifier, intended only to demonstrates the importance of multi-discipline system modeling.

A swept frequency response test, from 40 Hz to 1000 Hz, shows the effect of the complex amplifier loading by the voice-coil and speaker-cone dynamics*. The electro-mechanical resonances strongly affect the current that must be supplied, in order to maintain a flat (controlled) output voltage over the specified frequency range. For example, the current in the voice-coil reaches a null at time 0.1 seconds, which corresponds to the effective "spring-mass" resonance frequency (60 Hz). The loudspeaker reaches its minimum impedance around 600 Hz, or at 0.6 seconds where the peak load current is observed.

The simulation results also show that the average power (q1/npn/pwr_avg) in the BDP947 BJT exceeds its 5 Watt rating across the entire range, but especially at lower frequencies. The red "hot part monitor", with the junction to ambient thermal resistance set to 10 C/Watt, as given in the datasheet, shows the part temperature rising to over 100 C. These diagnostic indicators make it obvious that we need a bigger transistor!

All of the parameters in blue can be changed by the user and a new simulation run. The updated scope waveform results will show the effect of that change. You can change the electrical resistance and inductance of the voice-coil, as well as the speaker cone mass and linear spring rate that affect the resonance frequency.

* Note: Please refer to this companion example, that shows the input impedance frequency response of the loudspeaker alone:

https://www.systemvision.com/design/loudspeaker-only-frequency-response

About text formats

Terms of Use Cookie Notice Data Privacy Notice

GalinaDesigner21

Member for

GalinaDesigner21

Member for

angeltpDesigner237048

Member for

gilbert.velletDesigner236968

Member for

vladimir.jugDesigner236538

Member for

bbenoit1625Designer197752

Member for

juan.mendozarDesigner235029

Member for

clo21Designer235403

Member for

briangato.bbDesigner234763

Member for

pdhobby1213Designer234706

Member for

Galina
Designer21

Galina
Designer21

angeltp
Designer237048

gilbert.vellet
Designer236968

vladimir.jug
Designer236538

bbenoit1625
Designer197752

juan.mendozar
Designer235029

clo21
Designer235403

briangato.bb
Designer234763

pdhobby1213
Designer234706