PartQuest Explore Promote

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit - on Thu, 01/07/2021 - 11:15

sami.jaber
Designer237221

sami.jaber

Member for

3 years 5 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

LED Dimmer Circuit - on Thu, 01/07/2021 - 17:56

tingwei0116
Designer236121

tingwei0116

Member for

3 years 6 months

8

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 12/30/2020 - 16:44

usman.qasim1994
Designer237332

usman.qasim1994

Member for

3 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 12/30/2020 - 16:44

usman.qasim1994
Designer237332

usman.qasim1994

Member for

3 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit using 555 Timer - on Wed, 12/30/2020 - 16:44

usman.qasim1994
Designer237332

usman.qasim1994

Member for

3 years 4 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

Copy of LED Dimmer Circuit - on Sun, 12/20/2020 - 20:55

tanvirfakir
Designer237252

tanvirfakir

Member for

3 years 5 months

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

Copy of LED Dimmer Circuit using 555 Timer - on Sun, 12/06/2020 - 09:15

meriem.mehrez
Designer237025

meriem.mehrez

Member for

3 years 5 months

4

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!

LED Dimmer Circuit

Mike Donnelly
Designer19

Mike Donnelly

Member for

10 years 6 months

1,563

designs

10

groups

Member of the PartQuest Explore Development Team. Focused on modeling and simulation of analog, mixed-signal and multi-discipline systems covering a broad range of applications, including power electronics, controls and mechatronic systems.

Description

Copy of LED Dimmer Circuit using 555 Timer - on Sun, 11/15/2020 - 18:48

vladimir.jug
Designer236538

vladimir.jug

Member for

3 years 6 months

35

designs

groups

Add a bio to your profile to share information about yourself with other SystemVision users.

Description

This LED Dimmer Circuit uses a 555 Timer to control the PWM duty cycle of the current drive. Rather than apply proportional but continuous current to the LED for dimming, which can cause color shifts, modulating the duty cycle allows the LED to operate at its nominal current during the “ON” portion of the cycle. Because the frequency response of human vision is limited, using a PWM frequency of 250 Hz avoids the perception of flicker for the observer.

The LED model has an internal monitor for the "perceived" light output (blue waveform), which is a low-pass filtered version of the instantaneous light output. The filter pole frequency is set to 15 Hz to represent the bandwidth of the human eye. The value of the dimmer setting (green waveform) is increased from 10% to 90% at time 100msec. The LED current pulses (red waveform) are shown before and after the duty-cycle transition.

Part of this design is based on a dimmer schematic found on-line:

<a href="http://www.555-timer-circuits.com/led-dimmer.html">http://www.555-timer-circuits.com/led-dimmer.html</a>

That original circuit is actually incorrect, one of the diodes connected to pin 7 on the 555-Timer needs to be reversed. There was a comment from a reader who said he built the circuit as shown and it didn’t work. This is a good example of the value of simulating circuits before building hardware!